Amada Eco Products

All products developed by Amada are assessed in a variety of categories: energy conservation, resource conservation, recyclable resources, material use restrictions, consideration for the environment at the time of use, rationalization of packaging, and information provision.

Among Amada’s low environmental impact products, ones that have improved remarkably over previous models based on these assessments are called Eco Products.

FOL-3015AJ

eco product
The latest Laser Cutting Machine with in-house-developed fiber laser oscillator, achieves both high productivity and ecology.
Reduced the power consumption about 80% by new oscillator compared to the current model. Also, laser gas is not in need and lower running costs are achieved.

Click here for infomation on FOL-3015AJ

PCSAW-720

eco product
The next generation Band Saw Machine features pulse cutting, achieving high-speed, high-precision, low-noise processing.
Reduced the power consumption about 30% compared to the current model. It also reduces the noise by controlling the chattering vibration of the blade.

Click here for infomation on PCSAW-720

ACIES series

eco product
This Punch and Laser combination machine has ZR turret and full flat table resulting scratch less on bottom surface with high-speed process.
The power consumption is reduced by about 50% compared with existing model and the air consumption is also reduced by around 40% thanks to high efficient air purge unit.

  • ※These figures are on model ACIES-2512. Slight difference on other model.

Click here for infomation on ACIES Series

LC-C1NT series

eco product
Punch / Laser combination machine in compact size creating less set up time by various tool configuration(punching, forming & tapping)
35% reduction of power consumption by synchronized control of laser & punch axes compared with previous model.

  • ※The figure represents on LC1212C1NT, other models differ slightly

Click here for infomation on LC-C1NT Series

LC-F1NT series

eco product
3 axis Linear Motor Drive Laser Machine.
LC-F1NT achieves to reduce about 65% of power consumption by adopting energy-saving mode during standby compared to conventional machines.
Moreover, it also can reduce about 27% of the amount of lubricating oil use by a linear motor drive.

  • ※These figures are mentioned about LC-3015NT and somewhat different in case of other models.

Click here for infomation on LC-F1NT Series

AE-NT series

eco product
Punching machines equipped with an AC servo single drive.
The AE-NT series achieve an approximate 70% power consumption reduction compared to conventional machines. In addition, it reduces the need to use hydraulic fluid down to zero.

  • ※Figures are for the AE-255NT and may differ somewhat for other models.

Click here for infomation on AE-NT Series

HD-NT series

(8025/1703L/1703/3503/6006)All 5 models

eco product
Hydraulic bending machines equipped with a hybrid drive system composed of a high efficiency bi-directional piston pump and an AC servomotor. Their power consumption is about 50% of that of conventional machines and the volume of oil used has been reduced by approximately 50%. Energy and resource efficient, they significantly reduce environmental impact.

  • ※Figures are for the HD-8025NT and may differ somewhat for other models.

Click here for infomation on HD-NT series

SDEW series

eco product
The SDEW series are 2-point servo drive mechanical presses with servo-controlled motors.
They are capable of difficult stamping work through as abundant digital motions and/or strokes, resulting for prototype to mass production.

■Energy-saving :

The motor runs only when the slide activates through a control command. In addition, energy generated from slowing down or stopping the motor is recovered and stored in a condenser to be used as the next drive source. As a result, it consumes less power compared to flywheel-equipped mechanical presses in which the motor is running full-time.

■Resource-saving :

A circulating oil system has been adopted for the sliding section in place of the combination-type wet clutch/ brake used in conventional mechanical presses. As a result, the oil bath system is no longer necessary, so less lubricant is consumed.

Click here for infomation on SDEW Series

SDE Series

eco product
The SDE series are servo drive mechanical presses with servo-controlled motors.
They are capable of difficult stamping work through as abundant digital motions and/or strokes, resulting for prototype to mass production.

■Energy-saving :

The motor runs only when the slide activates through a control command. In addition, energy generated from slowing down or stopping the motor is recovered and stored in a condenser to be used as the next drive source. As a result, it consumes less power compared to flywheel-equipped mechanical presses in which the motor is running full-time.

■Resource-saving :

A circulating oil system has been adopted for the sliding section in place of the combination-type wet clutch/ brake used in conventional mechanical presses. As a result, the oil bath system is no longer necessary, so less lubricant is consumed.

Click here for infomation on SDE Series

EML-NT Series

eco product
The EML-NT series are "intelligent" punch/laser combination machines with AC servo direct twin drives on the punching drive.
In addition to oil free and energy saving features, the braking energy from RAM control is recovered and stored in a condenser, to be reused as energy for RAM acceleration. As a result, the EML-NT series offers significantly higher performance than conventional combination machines, while also saving energy and natural resources.

Click here for infomation on EML-NT series

Cutting fluid

16 types in all: MU601/ MU801 / CMW / RS /R / RL / SD / GR501 / SA / CTB / DP / AML-1 / AML-2 / AML-3 / AML-4 / AMADABARICOOL

eco product
These cutting fluids are free of chlorine, which generates dioxin during thermal recycling processes. They are also free of chemical substances controlled by PRTR* notifications.

  • ※Pollutant Release and Transfer Register

Click here for infomation on Cutting fluid